Hardware Podcasts

27: You Are Blowing My Mind

Embedded.fm · 13 Nov 2013

What this episode covers

Ivo Stivoric, co-founder of Body Media (now part of Jawbone), discusses the shift from simple pedometers to multisensor wearable systems that fuse data from motion, skin temperature, and heat flux to provide accurate health insights and behavior modification. Sam Guilaume and David Rothenberg of Movea explain their indoor navigation algorithm, which uses smartphone inertial sensors for dead reckoning at ultra-low power, and their strategy to harden parts of the sensor fusion logic into ASICs for efficiency. Stephen Walsh of ISKN presents iSketchnote, a MEMS-based pen and paper digitizer that captures handwriting and sketches in real-time, highlighting its successful Kickstarter campaign and transition from prototype to manufacturing.

Most relevant to

early-stage companies

Topics

Mentioned

Companies
Jawbone, Body Media, Movea, ISKN, Misty Microelectronics, Honeywell, New Life International
Products
iSketchnote
Also
LETI, CEA

Related episodes from other shows

Other shows on the same ground, closest first.

  • The Amp Hour · 1h 32m

    Gregory Charvat and Three New Companies

    Dr. Gregory Charvat, CTO of Humatics Corporation, discusses his three startups: Butterfly Network, Hyperfine, and Humatics. He details the pivot at Butterfly Network from high-cost ultrasound tomography to a handheld ultrasound on a chip using MEMS technology. He also describes Humatics' development of a short-range, high-precision indoor GPS system for factory automation, which achieved centimeter and millimeter accuracy through time-of-flight measurements.

    PCB design & layoutSensors & measurement in products
    7 chapters

  • The Amp Hour · 1h 06m

    An Interview with Noah Feehan - Biloquistic Blinking Blush

    Jason Kotki, a hardware engineer at the New York Times R&D Lab, discusses his work on experimental wearables and interactive art installations. He details the development of 'Blush,' a wearable that flashes when conversation topics match his browser history, and 'Fixture,' a device visualizing phone orientation. Kotki also describes building a thermal camera using the Panasonic GridEye sensor and shares his experience collaborating with Björk on the Biophilia project.

    Prototyping & iterationIndustrial & consumer product design
    8 chapters

  • The Next Byte Podcast · 21m

    249. Harvard’s Smartwatch Makes You Run Faster & Safer

    The hosts discuss research from Harvard’s School of Engineering and Applied Sciences, led by Connor Walsh, Daniel Lieberman, and Lauren Baker, which uses low-cost inertial measurement units (IMUs) to estimate ground reaction forces and running biomechanics. They explain how machine learning models trained on these inexpensive sensors can predict braking and propulsion forces with high accuracy, allowing for real-time feedback on running form and injury risk without laboratory equipment. The conversation highlights the potential for democratizing gait analysis through affordable wearables, noting the system's ability to adapt to new users within just eight steps.

    Sensors & measurement in productsAI & machine learning
    5 chapters

  • EE Times Current · 36m

    MEMS & Sensors Summit | WiFi & LoRa Make Nice | How to Blow A Recovery

    EE Times editors Nitin Dhadwal and Anne-Françoise Pele report from the MEMS & Sensors Summit in Grenoble, highlighting trends like sensor fusion with AI, 3D sensing, and medical applications such as subretinal chips. The episode also features a discussion with Bruno Thomas of the Wireless Broadband Alliance and Remy Loran of Semtech on how Wi-Fi and LoRaWAN protocols complement each other for IoT connectivity. Finally, Balaji Oja warns that the semiconductor memory market's notorious boom-and-bust cycles have returned, citing significant revenue declines at Samsung, SK Hynix, and Micron.

    Sensors & measurement in productsWireless & RF
    4 chapters

  • The Amp Hour · 1h 02m

    Garbage Ninjas

    Dave Jones and Chris Gammell discuss the engineering and marketing behind fitness trackers like the Fitbit Inspire 3, analyzing its sensors, Kalman filters, and the history of the 10,000-step metric. They review teardowns of the Fitbit and a 1980s boom box, highlighting component choices from STMicro and Maxim, and discuss the business of selling teardown reports via Yole Group. The conversation shifts to supply chain realities, including Chris Gammell's experience with Macrofab's DFM reports and the collapse of Tempo Automation, before touching on a compact RISC-V core implementation in Verilog.

    PCB design & layoutManufacturing partners & offshoring
    7 chapters

The summary, chapters and topics are generated from the episode’s audio by this directory, not written by Embedded.fm. The episode itself belongs to its publisher.