Hardware Podcasts

The Spark Gap - Episode 48

The Spark Gap · 28 Sept 2016 · 57m

What this episode covers

Hosts Carl and Corey discuss design choices for schematics and PCB layouts that facilitate easier board bring-up and debugging. They highlight specific components like current limiting diodes (1N5312) and bidirectional level shifters (SN74LVC1T45) to handle varying voltages and signal translation. The conversation emphasizes practical debugging strategies, including strategic package selection (QFP vs. BGA), the use of test points, and power isolation techniques using 0-ohm resistors to isolate faults during initial power-up.

Most relevant to

makers and hobbyists

Topics

Mentioned

Chips
1N5312, SN74LVC1T45
Also
Open Source Hardware Summit

Related episodes from other shows

Other shows on the same ground, closest first.

  • The Amp Hour · 1h 14m

    Assembly Chat

    Hosts Dave Jones and Chris Gammell record an episode while Dave assembles a PCB, discussing the utility of the Interactive BOM plugin for KiCad and the board repair software by Paul Daniels. They identify design flaws in Dave's board, including incorrect capacitor voltage ratings and missing silkscreen designators, and share technical tips on reliability, such as using series capacitors to prevent short circuits. The conversation also covers battery selection for cold environments, the OWASP Top 10 for hardware security, and vintage test equipment.

    EDA & CAD toolsDebugging & failure analysis
    6 chapters

  • The Amp Hour · 1h 04m

    Debugger vs Printeffer

    Dave Jones of EEVblog discusses the significant challenges he faced during the Kickstarter launch of his new digital multimeter, including manufacturing defects, logistical bottlenecks, and component sourcing issues. He details specific failures such as intermittent contacts in the range switch due to injection molding tolerances and units stuck in US customs due to reshipper ownership discrepancies. The conversation also covers the broader industry context of passive component shortages, the historical shift from mask ROM to reprogrammable microcontrollers, and debugging methodologies like using square waves for control loop stability.

    Crowdfunding & preordersQuality & yield
    7 chapters

  • The Amp Hour · 1h 04m

    Bubblegum Tap Shoes

    Dave Jones of EEVblog and Chris Gammell of Contextual Electronics discuss the technical nuances of 1N400x diodes, specifically why manufacturers produce multiple voltage ratings for the same package, and Gammell’s transition from Fusion 360 to FreeCAD. They also cover the internal operation of the LM317 linear regulator, the ongoing global semiconductor shortage affecting parts like the RP2040, and the importance of lab organization and measurement traceability.

    PCB design & layoutAnalog & power electronics
    8 chapters

  • The Amp Hour · 1h 04m

    Cores, Digikey, Electronic Design - The Commercial Competitor Commencement

    Chris Gammell and Dave Jones review the launch of a new DigiKey/DesignNews radio show, offering constructive criticism on its format, audio quality, and marketing approach. They discuss the technical challenges of semiconductor manufacturing at Intel, specifically 14nm lithography and yield management strategies like core disabling. The episode concludes with a discussion on component selection in low-cost electronics, such as using 9V batteries in multimeters, and the economics of mass production.

    PCB design & layoutChips, FPGAs & semiconductors
    6 chapters

  • The Amp Hour · 1h 17m

    Lowest Common Denominator Design

    Dave Jones and Chris Gammell discuss the acquisition of Maxim Integrated by Analog Devices, expressing concern over reduced component choice and the end of generous sample programs. They analyze Microchip's recent letter regarding lead times and the realities of semiconductor supply chain bottlenecks. The conversation shifts to PCB design challenges, specifically using JLCPCB's controlled impedance calculators and escaping fine-pitch BGAs using modified pad shapes. Finally, they review a detailed teardown report of a BMW i3 battery pack by Munro & Associates, highlighting the complexity of automotive manufacturing.

    Sourcing & supply chainPCB design & layout
    6 chapters

The summary, chapters and topics are generated from the episode’s audio by this directory, not written by The Spark Gap. The episode itself belongs to its publisher.