Hardware Podcasts

#067 - How to speed up your New Product Introduction - Production Line Tool, with Pete Staples of Blue Clover Devices, USA

The Hardware Entrepreneur · 13 Feb 2019 · 38m

What this episode covers

Pete Staples, co-founder and president of Blue Clover Devices, explains how his San Francisco and Shenzhen-based ODM company addresses production line inefficiencies through its new Production Line Tool (PLT). He details the high costs and rigidity of traditional automation, contrasting them with the PLT’s ability to automate testing for IoT devices at a fraction of the price, citing clients like Tesla, Volkswagen, and Scoot. Staples highlights the operational pain point of maintaining obsolete Standard Operating Procedures (SOPs) and describes how the PLT enables remote firmware loading and testing, offering a 10x cost improvement over conventional systems.

Most relevant to

companies scaling up

Topics

Mentioned

Companies
Blue Clover Devices, Tesla, Volkswagen, Audi, Scoot, Halter, Durolapse
Products
Production Line Tool
Also
FMEA

Related episodes from other shows

Other shows on the same ground, closest first.

  • The Amp Hour · 1h 19m

    Standardizing Manufacturing with Pete Staples

    Pete Staples, founder of Blue Clover Devices, an ODM with manufacturing in Shenzhen and design offices in the US, discusses the challenges of hardware production and the launch of their new product, the Production Line Tool (PLT). He explains how the PLT standardizes device programming and testing by combining power supply, J-Link, DMM, and Linux capabilities into a single box, allowing engineers to write YAML test plans that sync via cloud. Staples also details Blue Clover's strategic shift toward sustainability, aiming to be the 'Patagonia of electronics' by advocating for recycled materials and repairability among climate-conscious brands.

    Manufacturing partners & offshoringScaling production
    5 chapters

  • Embedded.fm · 54m

    309: Nature's Engineers

    Pete Staples, CEO and co-founder of Blue Clover Devices, explains how his company bridges the gap between hardware development and manufacturing through standardized testing tools. He details the Production Line Tool (PLT) and the ICT 100A fixture, which allow developers to run the same firmware programming and electrical tests in the office as on the factory floor, reducing handoff ambiguities. Staples also discusses the strategic decision to productize these tools to compete with giants like SEGGER and National Instruments, while addressing security concerns in their PLT Cloud system and the impact of tariffs on manufacturing flexibility.

    PCB design & layoutManufacturing partners & offshoring
    10 chapters

  • The Pragmatic Embedded Podcast · 50m

    Factory Firmware Flashing with Pete Staples

    Pete Staples, founder of Blue Clover Devices, explains the disconnect between engineering and manufacturing, noting that factory firmware flashing is often a dusty, manual afterthought rather than a sophisticated process. He details how Blue Clover’s Production Line Tool (PLT) and Test Agent standardize hardware and software to bridge the gap between engineer desks and factory floors, addressing security, provisioning, and calibration. Staples argues that engineers must define the test plan and 'good enough' criteria early to avoid costly emergency travel and production delays.

    Embedded firmwareManufacturing partners & offshoring
    9 chapters

  • Lights Out · 52m

    Lights Out Lenses: Engineering, Quality & the Leadership Behind Automation (Part 2), Ep #41

    Forrest Vaught, Director of Engineering & Programming at Advanced Machine & Fabricating, explains how standardization of tooling, fixturing, and programs is critical for successful automation in high-mix, low-volume environments. He details the logic of the FASTEMS 'Pistol Pete' system, which optimizes pallet selection based on tool life and due dates, and discusses the bottlenecks of feeding the system. Owner Scott Shortess reflects on the financial risks, the humility required to admit weak leadership, and how benchmarking in Europe exposed the need for automation to improve both throughput and employee quality of life.

    Scaling productionDesign for manufacturing & NPI
    6 chapters

  • EMS@C-LEVEL · 13m

    Bonus - That SCOOP Show Productronica Preview - Rob Raine and Alexander Hagenfeldt from ASM Assembly Solutions

    Rob Raine and Alexander Hagenfeldt from ASM Assembly Solutions discuss the company's 'open automation' strategy for the Productronica trade show, emphasizing modular, flexible production lines that integrate with industry standards like IPC-CFX and Hermes. They explain how ASM acts as an integration enabler, connecting SMT equipment with partners like VisCom and New Tech to help customers achieve a 'digital dividend' through real-time data flow and autonomous decision-making at the machine level. The conversation highlights the shift from simple automation to factory-level autonomy, catering to both incremental upgrades and fully automated 'lights out' visions.

    Manufacturing partners & offshoringFactory operations & automation
    6 chapters

The summary, chapters and topics are generated from the episode’s audio by this directory, not written by The Hardware Entrepreneur. The episode itself belongs to its publisher.